Chicago electric power tools wet saw

The saw has a powerful dual capacitor motor, a head that pivots to allow The saw also features an adjusting cutting head to adjust the blade. Chicago Industrial Tile Saw rips through large materials: 24 by 24 inch. The Chicago Industrial Tile Saw is not playing around when it comes to its power features. This industrial saw runs on a powerful dual capacitor motor with sealed bearings.

It runs on a good 2. Given that this saw runs on a very powerful and protected motor, you can be sure that it is going to last you several years, if not decades, if cared for and used properly. The Chicago Industrial Tile Saw uses a 10 inch diamond powder coated blade to rip through tough materials like butter. This industrial machine is strong enough to glide right through most materials like natural stone, marble, brick, granite etc in a matter of seconds!

The Chicago Industrial Tile Saw has a generously oversized stainless steel frame that has a linear bar system to ensure that your material smoothly glides through the blade. This control gives you clean, crisp cuts each time.

It has this heavy duty cast alloy cutting head to reduce vibrations during cutting as much as possible. Because Chicago Industrial Tile Saw is a wet tile saw like we mentioned before, it uses a water pump to douse water onto the working blade to cool it down and prevent overheating, and also catches dust and discarded particles from the ripped material. This saw uses a built-in 3 gallon per minute water pump for the purpose, and comes with a removable, east to clean and high-impact ABS water tub.

These cookies do not store any personally identifiable information. These cookies enable the website to provide enhanced functionality and personalization. They may be set by us or by third party providers whose services we have added to our Site. If you do not allow these cookies, then some or all of these services may not function properly, and your browsing experience may be degraded.

These cookies allow us to count visits and traffic sources so we can measure and improve the performance of our site. They help us to know which pages are the most and least popular and see how visitors move around the site.

They also help us identify sections of the site that can be optimized for the best browsing experience. All information these cookies collect is aggregated and therefore anonymous. If you do not allow these cookies, we will not know when you have visited our site, and will not be able to provide you the best experience possible.

Analytical cookies are used to understand how visitors interact with the website. These cookies help provide information on metrics the number of visitors, bounce rate, traffic source, etc. Other uncategorized cookies are those that are being analyzed and have not been classified into a category as yet. Advertisement cookies are used to provide visitors with relevant ads and marketing campaigns.

These cookies track visitors across websites and collect information to provide customized ads. Find a Store. ITC Prices. Get the App. Search for Deals. NEW Christmas Savings. Blade size 7 in. Depth of cut in. Shipping Weight Browse Our Most Viewed Deals. Air Compressors. Instant Savings. X When you visit our website, we store cookies on your browser to collect information.

And we had just over square feet of it to install… mostly on the walls… and half of it in a diamond pattern… with chair rail and decorative inserts. This was not a time to try out a wimpy saw particularly when you consider the density of porcelain vs ceramic tile. Chicago Electric is sold almost exclusively through Harbor Freight — a name that will bring to mind visions of bargain-priced inexpensive Chinese tools in some. It has a cast alloy body and two-position cutting head for handling both tile and masonry up to 3.

The frame is made of steel, with a squared-off welded base with plenty of supports and a tubular rim to which is attached the roller and sliding mechanism.

Chicago Electric Tools has a folding table stand with wheels, however a more robust third-party solutions might be better for long term use and storage. Tile cutting is done by placing a tile on the rolling cutting tray and then sliding the tray towards the inch diamond blade. The rolling tray is built out of the same sturdy steel, and has rubber pads on top to hold the tile securely in place and cushion it against vibrations during a cut.

Where the tray meets the steel frame there is a steel-on-steel guide system that allows the tray to slide along the left side. On the opposite side is a single small roller, centrally located along the length of the tray which guides the right side along the tubular right-side rail. The included 3 gallon per minute water pump is actually pretty robust. Over time we found that the pump got a tad weak and it actually worked best when plugged in separately and not via the 3A switched outlet located just off the power supply of the saw.

We did note a couple problems. One was that the clear hose that leads form the pump to the twin feeder tubes that douse the blade had a kink in it. The second issue was that one of the metal water tubes used to direct water to the blade was off, causing the water stream to miss the blade. We used a flat head screwdriver to bend the tube back into position and do a better job of cooling down the point of contact where the blade meets the tile during a cut.

The Chicago Electric tile saw comes with a straight edge guide as well as a degree miter guide which will allow you to make corner cuts on chair rail as needed. The included tray is made of ABS plastic and comes with a rubber stop that is attached to the tray with a chain.

I did like how light the plastic container was and that the drain could easily be unstopped to allow for draining of the majority of the water into a 5 gallon bucket. We really abused the heck out of this saw and used it for a variety of jobs, from simple ceramic tile to hard porcelain and even some brick cutting. One thing we never experienced was a lag in the motor or blade.

No matter what we fed the saw, the blade never bogged down or lacked for power. That means that this saw is about as good as the blade you put in it. Blade changes were quick and easy. To allow the 2. To the left of the power supply and blade stop, a metal cover surrounds the belt system that drives the blade axle. Replacing the belt is a simple function of removing the belt cover with two hex wrenches and accessing the drive system underneath.

Lighter ceramic tile the saw cut through pieces like butter. It also sliced through brick like it was made of play-dough. When pushing the tray through the cut there is a bit of friction and you really need to push from the left side where the hinge and guide assembly is located. Pushing from the right seemed to bind the tray, even with ample amounts of WD sprayed all over the guide system.

The excessive binding is due to the lack of bearings and a guide which relies on distribution of friction across a large area of rounded steel piping. The inch diamond blade we were using, which we purchased at Harbor Freight with the saw, was a tad on the thick side, but even so did an adequate job of slicing though all sorts of tile. In cutting through porcelain in a diagonal pattern, we found that applying equal pressure to the tile and allowing the saw to cut through it gradually — without forcing the blade through — yielded the best results.

One of the downsides with this saw vs. The water jets also did an excellent job of covering the blade and ensuring that the cutting path was completely cooled and that dust from the cut was kept to a minimum.