Cast iron insert fireplace installation

The ability to cook on them would just be for times of power outages and such - not something we'd do often but seems like a nice value add. The T5 insert would fit pretty well width wise, but would leave a gap at the top that I'd have to fill in somehow. Why would you go with the F over the others, if you had a good dealer? Jan 10, 21 SE PA. I have a Jotul F installed in my fireplace. It works great but is is the older version. Dimensionally this should work Depending on the size of your hearth.

No matter which you choose get their manual online first and check all the clearances. It was close with my Jotul. My particular set up makes it tough to clean the chimney but I hire it out. That is something else worth thinking about when you make your decisions. Would you mind sharing a picture? I had a chimney sweep out last week who cleaned and inspected everything.

If I go with the F it would be a little tight for sweeping, but if I get the short leg kit that would allow a little more room. Make sure there is room for the side door to open. May 22, Utah, NJ. I have a Jotul f and am very happy with it. It would fit better in your fireplace. So you will rear vent it? Pretty easy to clean the liner with a clean out T. Did you rule out a PE T5 or T6 tucked way back in? Yes, planning to rear vent the Jotul. Since they are top vent only, they would have to be set in there pretty deep.

The T6 would only have about 1. The T5 would have a little more on the sides. Probably too tight to even install, and I'd not be able to cook on it in case of need. So unfortunately the PEs are out. Thus the recommendation for the T5 insert with the oversized surround.

The main issue there becomes the surround covering up the fireplace tiles, which is what moved my toward stoves to begin with. Last edited: Dec 17, Alright things are starting to come together. Does that sound reasonable? I have no context since I've never done this before. They do have insulated "models". Ceramic has been used on fireplace surrounds and hearths for hundreds of years.

Porcelain is also a great pick for the fireplace. Glass is a stunning choice for the fireplace. Stone is another excellent choice for the fireplace.

You really need a fireback if the back wall of the fireplace is damaged by the fire. In addition, a fireback has the additional advantage that the cast iron of the fireback is warmed by the fire and the fireback therefore radiates extra heat. Afterwards, smooth down the surface using fine wire wool and a rust remover, then wipe with white spirit, not water, to prevent new rust stains. Insert the lower section of the fireback into the fireplace recess with the front level with the front of the builders opening.

Place corrugated cardboard or thin strawboard against the rear and sides of the fireback intended to char in use to leave an expansion gap. Loose tiles are slightly harder to fit we recommend lying them flat in pattern then turn them over and apply a few strips of gaffer tape again attach straps then slide them in again loosely tighten wing nuts till top and bottom tiles are secure pack centre tiles out with a little cardboard or filler then cement all the.

Fireplace inserts are a more efficient heat source than traditional fireplaces. You can save money on your energy bill if you install a fireplace insert. A more efficient wood-burning heating system means less gas, oil, or electricity is required to heat your home. Installing a fireplace insert is ideal when you have an existing fireplace of some sort. It is a less expensive option when compared to renovation or replacement. Inserts replace the inefficient wood burning system of an open masonry fireplace and vent through an existing chimney.

The primary difference is that a fireplace insert is an appliance that can be installed into an existing wood burning fireplace to make it more efficient.

There are inserts that burn wood, gas with a direct vent system, and gas inserts that do not require a vent. In most cases, you cannot take just any old stove and place it in front of or in such a fireplace and pipe it up.

Mark is a seasoned green industry veteran and freelance writer based in Georgia. His work encompasses all things garden, landscape, home improvement, and DIY, with a focus on sustainability. He occasionally blogs about his gardening adventures at theprudentgarden. Select Region. United States. United Kingdom. Home Improvement Interior. Advertiser Disclosure. By Mark Wolfe. We earn a commission from partner links on Forbes Home. Commissions do not affect our editors' opinions or evaluations.

Find a Fireplace Installer. When To Install a Fireplace Insert If you have an existing masonry fireplace, installing a fireplace insert could make sense. Prepare the Fireplace Opening Use an angle grinder or cutting torch to remove the damper, located inside the chimney. Install the Flue Vent Liner At the top of the chimney, attach the pulling cone and rope to one end of the flue liner.

Install the Fireplace Insert Back down at the fireplace opening, attach the vent adaptor to the end of the flue vent liner. Install the Chimney Cap At the top of the chimney, trim the flue vent liner to length with snips. Install the Trim Complete this fireplace insert installation by attaching the trim. Home Improvement. More from. Information provided on Forbes Home is for educational purposes only. The products and services we review may not be right for your individual circumstances.

Forbes Home adheres to strict editorial integrity standards. To the best of our knowledge, all content is accurate as of the date posted, though offers contained herein may no longer be available. Mark Wolfe Contributor.