Yamaha rx-v1400 manual

Automatic tuning is effective when station signals are strong and there is no interference. This function enables this unit to automatically tune in to FM stations with strong signals, and to store up to 40 8 stations x 5 groups of those stations in order.

Page Selecting Preset Stations Selecting preset stations You can tune any desired station simply by selecting the preset station number under which it was stored. Refer to the operation instructions for those components. A classic shoe-box type concert hall with approximately seats. Pillars and ornate carvings create extremely complex reflections which produce a very full, rich sound. If you display the SET MENU and sound field program parameter settings on a monitor, it is much easier to see the available options and parameters than it is by reading this information on the front panel display.

Page Set Menu You can use the following parameters in the set menu to adjust a variety of system settings and customize the way this unit operates. Change the initial settings indicated in bold under each parameter to reflect the needs of your listening environment.

INI Initializes the parameters of a group of sound field programs. SP IMP. Ideally, each speaker should be the same distance from the main listening position.

However, this is not possible in most home situations. Page 57 Headphone tone control Use to adjust the amount of bass and treble output to your headphones. INI Use this feature to initialize the parameters for each sound program within a sound program group. When field field you initialize a sound program group, all of the field parameter values within that group revert to their initial settings.

To control other components, you must set up remote control with the appropriate manufacturer codes. This remote control also has a learn feature which allows the remote to acquire functions from other remote controls equipped with an infrared remote control transmitter.

In this case, try to set other Yamaha manufacturer code s. Press an input selector button to select the source component you want to set up. If operation is not possible with any of the manufacturer codes, program the new remote control function with the Learn feature see below or use the remote control supplied with the component.

In this case, start over from step 5. Page Clearing Function Sets Clearing function sets You can clear all changes made in each function set, such as learned functions, renamed source names and setup manufacturer codes.

Other wise, the learning mode will be automatically canceled. Note that some buttons may not correctly operate the selected component. Use the input selector buttons to select the component you want to operate. If you own these products, you may not need to use an infrared emitter. You can even select the input source and control components located in the main room directly from the second room regardless of the listening condition in the main room.

Page Editing Sound Field Parameters The acoustics in your room could be changed to those of a concert hall, a dance floor, or virtually any size room at all. Not all of the following parameters are found in every program. Description: The early reflections of a sound source decay much faster in a room with acoustically absorbent wall surfaces than in one which has highly reflective surfaces.

Page 79 REV. TIME Reverberation time Function: This parameter adjusts the amount of time it takes for the dense, subsequent reverberation sound to decay by 60 dB at 1 kHz. This changes the apparent size of the acoustic environment over an extremely wide range.

LIFT Dialog lift Function: This parameter adjusts the height of the front and center channel sounds by assigning some of the front and center channel elements to the presence speakers. Description: The larger the parameter, the higher the position of the front and center channel sound. Page Troubleshooting Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center.

The sleep timer has turned the unit off. The sound is muted. Only the speaker on Incorrect cable connections. Dolby Digital signals. The picture is The video source uses scrambled or disturbed. Page 85 Remote control Problem The remote control Wrong distance or angle. Direct sunlight or lighting from an inverter type of fluorescent lamp, etc. If you have any problems opening files please read the download FAQ. All files are provided under strict licence and reproduction without prior permission or for financial gain is strictly prohibited.

If you have additional documentation please consider donating a copy to our free archive. I agree with your opinion regarding the amplifier. It seems to lack 2-channel muscle. However in its theater modes is when this receiver sounds best imo. But I listen to music more than watch movies or tv so I tend to want a system which can handle my requests. Therefore I opted for two separate systems- a digital and a analog based set ups. One for THX movies, etc.

The other for playing records and tapes in 2 or 4 channel with a active subwoofer. Both have a dedicated CD player and iPod connections for the hell of it. Best of both worlds. Overall, I think Yamaha has a lackluster sound that might be too natural for me.

Every room and components vary as the sound quality of many formats diminish. If they want me to hear as it should be I've bought this receiver new back in and still use it.

Can't get the most out of it I think because I'm not hearing the watts it should be able to produce. Playing direct stereo or 2ch channel stereo with or without "straight" effect still gives a weak sound compared to a true stereo amp. Too many options for speaker size and countless other settings. Can anyone please help me with this issue. I have the original owners manual,settings microphone and I'm a huge Yamaha fan.

Would like to get it playing as it should. Speakers used:Infinity Beta 50,20,C and sub sw